WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Type B RCD Protection for AC and DC Leakage in Wallbox Chargers

By shincharge November 11th, 2026 16 views

Introduction: Type B RCDs matter in AC wallbox chargers because smooth DC residual current behaves differently from ordinary AC leakage and needs its own detection path.

A wallbox charger is often described by its power rating, connector type, cable length, or app features, but the leakage protection line deserves separate attention. Ordinary AC leakage protection is built around alternating current. An EV connected to an AC wallbox also contains power electronics and a high-voltage battery, so a fault path can carry smooth DC residual current. That difference changes what the protection device has to notice. Understanding the distinction helps readers interpret a Type B RCD label and the 6mA DC figure without treating them as interchangeable safety words.

Why AC leakage protection alone does not cover smooth DC residual current

Think of a shared parking garage where a car stays connected overnight. The visible parts are simple: an AC wallbox, a charging cable, and a vehicle inlet. The less visible part is the vehicle’s onboard charger, which converts AC into DC for the battery. That onboard charger includes rectifiers, switching devices, capacitors, and isolation barriers. If a fault develops on the DC side or in the isolation path, residual current can take a form that is no longer a clean AC waveform. A standard AC leakage device is designed around the expected shape of AC residual current, so it is the wrong tool for the smooth DC case. The mechanism is easier to picture through the current transformer used in many residual current devices. The device watches the outgoing and returning conductors. In a healthy circuit, the currents balance. In a leakage event, the difference produces a magnetic flux that the device senses and uses to trip. A smooth DC residual current can push the transformer core into one direction and reduce its ability to respond to the AC signal the device is looking for. The practical result is that an AC-only protection layer may not reliably detect a smooth DC fault, or it may lose sensitivity. That is why a wallbox charger with an EV attached needs a protection concept that includes DC leakage, not just ordinary AC leakage. This matters because the wallbox is not an isolated box on a wall. It is the supply point for a vehicle with its own power conversion equipment. The charger and the vehicle together form the operating scene. A Type B label on the wallbox tells a reader that the protection path is intended to include smooth DC residual current, alongside the more familiar AC leakage case. The label is not a substitute for installation design, but it is a useful signal that the charger’s protection line has been written for the mixed AC and DC world of EV charging.

How Type B RCDs respond to AC, pulsating DC and smooth DC leakage

A Type B RCD is best understood as a protection device that does not stop at the AC case. It adds detection for residual currents that have a DC component, including the smooth DC current that ordinary AC devices can miss. The exact sensing method varies by design, and the device may use a combination of current transformers, DC-sensitive sensing, and electronic evaluation. The useful learning point is not the internal brand of sensor. It is that the device is specified to respond across three leakage shapes, because EV charging can produce all three.

  • AC residual current is the familiar alternating leakage that rises and falls with the supply waveform. A Type B RCD keeps the AC detection idea: it compares outgoing and returning current, sees the imbalance, and trips when the residual current crosses the AC threshold. In a 30mA AC rating, that is the alternating-current part of the protection line.
  • Pulsating DC residual current flows mainly in one direction but still has a changing, ripple-like shape, often linked to rectified AC. The detection idea is to recognize that the current is not a pure sine wave while still responding to its changing component. Type A protection covers part of this family; Type B extends the protection concept to DC components that a purely AC device is not built to handle.
  • Smooth DC residual current is nearly constant in one direction and has no zero crossing to help a conventional AC sensor. The detection idea is direct DC-sensitive monitoring: the device watches for a steady residual current and opens the circuit before that current can sit unnoticed. This is the leakage type that makes Type B coverage meaningful in an AC wallbox.

The list also explains why “Type B” is not just a higher number on a datasheet. It describes a wider detection job. An AC-only device is built for a world where leakage follows the supply waveform. A Type B device is built for a world where a vehicle’s onboard electronics can create residual current with a DC offset or a smooth DC shape. When a wallbox EV charger manufacturer states Type B leakage protection, the reader can understand that the protection line is meant to cover the AC case, the pulsating DC case, and the smooth DC case rather than assuming one waveform stands for all leakage.

What 6mA DC monitoring adds to the protection picture

The 6mA DC figure is often the most misunderstood part of a wallbox protection label. It is not a second name for Type B, and it is not a general current rating for the charger. It is a DC residual current monitoring threshold. In an AC wallbox, a dedicated DC monitor watches for smooth DC residual current and opens the circuit when that current reaches the monitored threshold. This gives the protection chain a sensitive DC layer that sits alongside the AC leakage protection. The point is to catch smooth DC early, before it becomes a larger residual current problem in the installation. The ShinCharge Z4 series lists Type B leakage protection at 30mA AC plus 6mA DC / CCID20. That line is useful because it shows both sides of the leakage story in one place: an AC threshold and a DC monitoring threshold. The same specification also groups overcurrent, grounding, surge, overvoltage, undervoltage, overfrequency, underfrequency, and overtemperature protection under the charger’s protection set, but the leakage line is the one that matters for this discussion. For a reader learning the terms, the important lesson is that 6mA DC monitoring adds a dedicated DC watchpoint; Type B describes the broader residual current coverage. The two facts belong together, yet they describe different layers of the same protection idea. Wall charger suppliers often compress this into a short label because buyers need a quick way to compare models. A wall charger factory may print “Type B” and “6mA DC” on the same line, and that is fine as a summary. The label becomes clearer when the reader knows that one part addresses AC leakage and the other part addresses smooth DC residual current. Site design, protective earthing, circuit selection, and local electrical rules still govern the actual installation. A 6mA DC monitor supports the protection chain; the installation as a whole remains the responsibility of the qualified designer and installer.

Conclusion

Type B RCD protection in an AC wallbox is easier to understand when the leakage types are kept separate. Ordinary AC leakage protection follows the alternating waveform. Pulsating DC leakage has a changing DC component. Smooth DC leakage is steady enough that a conventional AC sensor may lose the signal it needs. A Type B RCD is specified to respond across those leakage shapes, while 6mA DC monitoring adds a dedicated watchpoint for smooth DC residual current. The ShinCharge Z4 series is one reference example that states 30mA AC plus 6mA DC / CCID20 on its protection line. That label is most useful when read as part of a complete electrical design, not as a standalone installation answer.

FAQ

Q: What does a Type B RCD protect against in an AC wallbox charger?

A: A Type B RCD protects against residual current that includes AC, pulsating DC, and smooth DC components. In an AC wallbox, the AC part covers ordinary alternating leakage, while the DC-sensitive part addresses current created by the vehicle’s power electronics. This matters because an AC-only device may not reliably detect smooth DC residual current.

Q: Why is smooth DC residual current different from ordinary AC leakage?

A: Ordinary AC leakage rises and falls with the supply waveform, so an AC residual current device can sense the changing imbalance. Smooth DC residual current flows steadily in one direction and has no zero crossing. That steady DC can affect the current transformer inside an AC device and reduce its ability to respond, which is why a DC-sensitive protection layer is needed.

Q: What does 6mA DC monitoring mean in a wallbox charger?

A: It means the charger includes a DC residual current monitor that watches for smooth DC leakage at a 6mA threshold and opens the circuit when that threshold is reached. It is a dedicated DC layer in the protection chain, separate from the AC leakage threshold. Type B coverage and 6mA DC monitoring are related, but they describe different parts of the same protection picture.

Sources / References

ISO/IEC 8825-2:2015/COR1:2017

Alternative Fuels Data Center: Procurement and Installation for Electric Vehicle Charging Infrastructure

Related Examples

ShinCharge wall-mounted EV charger specification reference

Previous
AC Wallbox Factory Checks from Assembly to Final Inspection
Read More