Introduction: An AC wallbox draws alternating current from a dedicated home circuit, feeds it to the car, and leaves the AC-to-DC conversion to the vehicle's onboard charger.
The box on the garage wall is often called a charger, and that label causes most of the confusion. In a home AC setup the wallbox is a supply point: it draws alternating current from the electrical panel, manages how much the car may take, and hands that current over through the cable. The conversion to direct current — the form a battery actually stores — happens inside the vehicle. Tracing that path once, from panel to wallbox to vehicle inlet to onboard charger to pack, makes ratings, cable choices and charging speeds much easier to read, and it explains why two neighbours with identical wallboxes can see very different numbers on the screen.
The electrical panel is where the story begins. Power arrives at the property as alternating current, and the panel splits it into branch circuits, each protected by its own breaker. An AC wallbox sits at the end of one of those circuits, normally a dedicated one that serves nothing else. That circuit is permanent fixed wiring rather than a plug-in lead, which is why the work belongs to a licensed electrician following local electrical codes. From the wallbox's point of view, the panel is simply the source: a live, neutral and earth connection that can deliver current steadily for hours rather than in short bursts. The wallbox is best understood as a controlled gateway. It does not create energy or raise the voltage; it decides whether current may flow, how much the car can take, and when to stop. When a cable is plugged in, the unit signals the maximum current available on that circuit, waits for the vehicle to confirm it can accept that amount, and only then closes its internal contactors to connect power. The rest of the enclosure is protection and feedback — a Type B RCD rated 30 mA AC plus 6 mA DC, over-voltage and under-voltage monitoring, surge protection, over-current and over-temperature cut-outs, and a display showing what the unit is doing. A wall-mounted model such as the ShinCharge Z4 series, with a 250 × 250 × 90 mm control box, a 7-inch LCD and 5 m, 7 m or 10 m TPU cable options, shows that mix clearly: switching hardware, safety hardware and a small status screen.
Follow the current past the wallbox and the picture changes. Energy leaves the panel as alternating current and arrives at the battery as direct current, and the equipment that performs the change sits inside the vehicle rather than on the garage wall. That single fact explains most of the confusion around charger names, rating labels, and why a bigger wallbox does not automatically mean a faster charge.
What enters the wallbox as AC leaves it as AC. There is no rectifier stage inside an AC wallbox and no DC output terminals; the enclosure switches, protects and measures the supply, then hands alternating current to the cable. Designers place the conversion in the car for practical reasons. One onboard converter can serve every AC source a driver meets, from a home wallbox to a workplace post, and the wall hardware stays smaller, cooler and cheaper to replace. That is why an AC wallbox works alongside the vehicle's onboard charger rather than in place of it.
Inside the car, the onboard charger turns that alternating current into direct current at the voltage the pack needs, adjusting current as the battery management system requests. This is the stage that sets the real ceiling for AC charging, and it is fixed by the vehicle rather than by the unit on the wall. It also explains a small detail drivers notice on the first evening: the wallbox display reports the AC current and power flowing through the cable, while the car's own screen reports what reached the pack. The two numbers differ slightly because conversion and heat both take a small share.
Real charging speed is set by the lowest of three ceilings: what the home circuit can supply continuously, what the wallbox is rated to deliver, and what the car's onboard charger can accept. A vehicle with a 7 kW onboard charger fed by an 11 kW unit will still charge at roughly 7 kW, with the extra capacity sitting unused. For the same reason, the ratings published by wall charger suppliers and wallbox EV charger manufacturers describe equipment capability rather than a promised charge time. They tell you what the hardware can deliver on a suitable supply; matching that hardware to a particular car is a separate question. The battery adds a fourth, moving limit. Charging is rarely a flat line from empty to full. It is usually quickest in the middle of the state of charge and tapers near the top, and a cold pack accepts less current than a warm one until it warms up. That is why the same car on the same wallbox can show different numbers on different evenings with nothing faulty. Treating the figure on the screen as a fixed property of the charger is the most common misunderstanding in home AC charging. This is also why one wallbox family is sold in so many versions. The Z4 series, for example, comes in Type 2, Type 1 and NACS versions with ratings from 7 kW to 22 kW, and the sensible choice depends on the vehicle inlet and on the supply available at the property. A home EV charger decision is therefore a three-way match between the panel, the unit and the car — and the weakest link in that chain is what the driver actually experiences at the plug.
The energy path is short and worth remembering: panel, circuit, wallbox, cable, vehicle inlet, onboard charger, battery. Alternating current travels all the way to the car, and the vehicle performs the conversion. Everything on the wall handles switching, protection and communication, which is why a larger wallbox cannot force a faster charge than the car will accept. When comparing units, the useful questions are what the home circuit can support, what the vehicle's onboard charger can take, and how clearly the unit reports what is happening. Readers who want to check the specifications of a wall-mounted AC unit can review the Z4 series product information as a reference point.
A: No. An AC wallbox passes alternating current through to the vehicle and contains no rectifier stage. Its job is to switch, protect and communicate: it tells the car how much current is available, waits for confirmation, then closes its contactors and lets current flow. The AC-to-DC conversion happens in the vehicle's onboard charger, which delivers direct current to the battery at the voltage and current the pack management system asks for.
A: The panel sets the supply ceiling. The dedicated circuit and its breaker determine how much current the wallbox can draw continuously, and the unit signals that limit to the car before charging begins. If the circuit supports less than the wallbox rating, the circuit becomes the bottleneck. If it supports more, the car's onboard charger usually becomes the limiting factor instead. This is why the supply side and the vehicle side have to be considered together.
A: Because onboard chargers differ from model to model. A car with a 7 kW onboard charger will draw about 7 kW even from an 11 kW wallbox, while a model with an 11 kW unit can use more of the available capacity. Battery size, state of charge and pack temperature add further variation, including on the same car from one session to the next. The wallbox supplies the current; the vehicle decides how much of it to accept.
Recharging systems | European Alternative Fuels Observatory